- UID
- 565107
- »ý·Ö
- 36
- ÉùÍû
-
- ²Æ¸»
-
- ÁúÖé
-
- ͱÒ
-
- »ØÌû
- 0
- Ö÷Ìâ
- ÌýÖÚ
- ÊÕÌý
- ÐÔ±ð
- ±£ÃÜ
- Äê¶È»ý·Ö
-
- ÔÚÏßʱ¼ä
- Сʱ
- ×¢²áʱ¼ä
- 2021-12-1
|
»ìÄýÍÁ»¯·à³ØÄ£¾ßÓÃÓÚÖÆ×÷Ïñ¶À¾Ó»§¡¢Ñ§Ð£¡¢ÂÃÓξ°µãµÈµØ·½µÄ»¯·à³Ø£¬ÒªÏëÖÆ×÷Ò»¸öÖÊÁ¿ºÏ¸ñÓÃʹ
ÓÃʱ¼ä³¤¾ÃµÄ»ìÄýÍÁ»¯·à³ØÄ£¾ßÐèҪעÒâÒÔϼ¸µã1.¸ù¾Ý¿Í»§ÐèÇóÌṩµÄÉè¼ÆʦͼֽÖÆ×÷³öÏà¶ÔÓ¦³ß
´çµÄÄ£¾ß£¬È»ºóʹÓÃÄ£¾ßÖÆ×ö»ìÄýÍÁ»¯·à³Ø£¬Ä£¾ßÓÐËÜÁÏÄ£¾ßÓиÖÄ£¾ß£¬ºÜ¶à¹¤³Ìϲ»¶Ñ¡È¡¸ÖÄ£¾ß£¬
ÒòΪ¸ÖÄ£¾ßµÄʹÓÃʱ¼ä³¤¾Ã¡¢³ÐÊÜÁ¦´ó¼á¹Ì£¬½¨ÒéʹÓøְåÒòΪ±ÈÆðÆÕͨ¸Ö°å¸Ö°åʹÓõÄʱ¼ä³¤¾Ã£¬
2.Ê©¹¤Ê±ÎªÁËÈûìÄýÍÁ»¯·à³ØÄ£¾ßÖÆ×÷µÄ»¯·à³ØÍâ±íÃÀ¹Û¶ÈÔö¼Ó£¬ÔÚ×¢Èë»ìÄýÍÁÕð¶¯ÍêÖ®ºóÐèҪʩ¹¤
ÈËÔ±Óùΰå°ÑËüµÄ±íÃæĨƽ£¬È»ºó½¨ÒéͿĨÉÏÓÍÆᣬÕâÑùÈû¯·à³ØµÄʹÓÃʱ¼äÑÓ³¤²»»áË𻵣¬Æðµ½Ò»
¸ö±£»¤»¯·à³ØµÄ×÷Óã¬3.µÈ»ìÄýÍÁÍêÈ«Äý¹Ìºó£¬ÍÑÍêÄ£ÐèÒª¶ÔÄ£¾ß½øÐм°Ê±µÄÇåÏ´£¬Èç¹ûÇåË®ÇåÏ´²»
¸É¾»µÄ»°£¬Òª¼°Ê±Ê¹ÓÃÏ¡ÊͺóµÄ²ÝËá¶ÔÄ£¾ß½øÐÐÇåÏ´£¬È»ºóÓÃË¢×ӰѱíÃæ²ÐÁôµÄ»ìÄýÍÁ²ÐÁôÎïË¢¸É¾»
£¬ÓÃרÃŲÁÄ£¾ßµÄĨ²¼°ÑÄ£¾ß±íÃæµÄË®·Ö²Á¸É¾»£¬±ÜÃâ³öÏÖÉúÐâµÄÏÖÏó£¬ÕâÑù¼´·½±ãÄ£¾ßÏ´ÎʹÓã¬
ÓÖÄÜʹģ¾ßµÄʹÓÃÊÙÃüÑÓ³¤¡£
The concrete septic tank mold is used to make septic tanks in places such as single
households, schools and tourist attractions. In order to make a concrete septic tank mold
with qualified quality and long service life, we need to pay attention to the following
points 1 According to the designer's drawings provided by the customer's needs, the molds
with corresponding dimensions are made, and then the molds are used to make the concrete
septic tank. The molds include plastic molds and steel molds. Many projects like to
choose steel molds because the steel molds have long service time and strong bearing
capacity. It is recommended to use steel plates because they are used for a long time
compared with ordinary steel plates. 2 During construction, in order to increase the
appearance of the septic tank made of the concrete septic tank mold, after the concrete
is injected and vibrated, the construction personnel need to smooth its surface with a
scraper, and then it is recommended to apply paint, so as to prolong the service time of
the septic tank without damage and protect the septic tank. 3 After the concrete is
completely solidified, the mold needs to be cleaned in time after removing the mold. If
the clean water is not clean, the mold should be cleaned with diluted oxalic acid in
time, then the residual concrete residue on the surface should be brushed with a brush,
and the water on the mold surface should be wiped with a special rag to avoid rust, This
not only facilitates the next use of the die, but also prolongs the service life of the
die.
|
|